{"id":32736,"date":"2026-06-30T03:42:45","date_gmt":"2026-06-30T03:42:45","guid":{"rendered":"https:\/\/www.beskamold.com\/?p=32736"},"modified":"2026-06-30T03:44:25","modified_gmt":"2026-06-30T03:44:25","slug":"straightness-vs-flatness-in-gdt","status":"publish","type":"post","link":"https:\/\/www.beskamold.com\/es\/straightness-vs-flatness-in-gdt\/","title":{"rendered":"Straightness vs Flatness in GD&#038;T: Key Differences and When to Use Each"},"content":{"rendered":"<div data-elementor-type=\"wp-post\" data-elementor-id=\"32736\" class=\"elementor elementor-32736\" data-elementor-post-type=\"post\">\n\t\t\t\t<div class=\"elementor-element elementor-element-5e4ad40 e-flex e-con-boxed e-con e-parent\" data-id=\"5e4ad40\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t\t<div class=\"e-con-inner\">\n\t\t\t\t<div class=\"elementor-element elementor-element-6a71767 elementor-widget elementor-widget-text-editor\" data-id=\"6a71767\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<p>Two engineering drawings may look almost identical. One specifies straightness, while the other specifies flatness. The difference seems minor, but it can affect how a part is machined, inspected, and assembled.<\/p><p>Straightness and flatness are both GD&amp;T form tolerances, but they control different aspects of a part&#8217;s geometry. Straightness controls a single line or axis, while flatness controls an entire surface. Using the wrong tolerance can increase manufacturing costs, complicate inspection, or even cause <a href=\"https:\/\/www.beskamold.com\/es\/mechanical-assembly-service\/\">assembly<\/a> problems.<\/p><p>This guide explains the differences between straightness and flatness, when each tolerance should be used, and how to apply them correctly in engineering drawings. It also covers common mistakes, inspection methods, and practical selection guidelines for engineers and quality professionals.<\/p><h2>1. What Is Straightness in GD&amp;T?<\/h2><p><img fetchpriority=\"high\" decoding=\"async\" src=\"data:image\/gif;base64,R0lGODlhAQABAIAAAAAAAP\/\/\/yH5BAEAAAAALAAAAAABAAEAAAIBRAA7\" data-src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT.jpg\" class=\"alignnone size-full wp-image-32738 lazyload\" alt=\"What Is Straightness in GD&amp;T\" width=\"1080\" height=\"550\"><noscript><img decoding=\"async\" class=\"alignnone size-full wp-image-32738\" src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT.jpg\" alt=\"What Is Straightness in GD&amp;T\" width=\"1080\" height=\"550\" srcset=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT.jpg 1080w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT-300x153.jpg 300w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT-1024x521.jpg 1024w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT-768x391.jpg 768w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Straightness-in-GDT-18x9.jpg 18w\" sizes=\"(max-width: 1080px) 100vw, 1080px\" \/><\/noscript><\/p><p>A shaft passes inspection. The report says it is straight within 0.05 mm. But it binds in the bearing during assembly. The machinist says the part is good. The inspector says it passes. The assembler says it does not fit.<\/p><p>The drawing called out straightness, but it did not specify which type.<\/p><p>Straightness in GD&amp;T comes in two forms. Surface straightness controls line elements on a surface, while axis straightness controls the centerline of a cylindrical feature. Although they share the same symbol, they are applied and inspected differently. The wrong callout means parts can pass inspection but still fail assembly. This is not a theoretical issue. It happens on the shop floor more often than most engineers realize.<\/p><h2>2. What Is Flatness in GD&amp;T?<\/h2><p><img decoding=\"async\" src=\"data:image\/gif;base64,R0lGODlhAQABAIAAAAAAAP\/\/\/yH5BAEAAAAALAAAAAABAAEAAAIBRAA7\" data-src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT.jpg\" class=\"alignnone size-full wp-image-32739 lazyload\" alt=\"What Is Flatness in GD&amp;T\" width=\"1080\" height=\"550\"><noscript><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-32739\" src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT.jpg\" alt=\"What Is Flatness in GD&amp;T\" width=\"1080\" height=\"550\" srcset=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT.jpg 1080w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT-300x153.jpg 300w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT-1024x521.jpg 1024w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT-768x391.jpg 768w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/What-Is-Flatness-in-GDT-18x9.jpg 18w\" sizes=\"(max-width: 1080px) 100vw, 1080px\" \/><\/noscript><\/p><p>A surface looks flat. It feels smooth. But when the quality team checks it on a CMM, the readings show a wave across the whole face. The surface is smooth, but it is not flat.<\/p><p>Flatness controls the entire surface, not just one line. Every point on the surface must lie within two parallel planes. Unlike many other GD&amp;T controls, flatness does not require a <a href=\"https:\/\/www.beskamold.com\/es\/what-are-datums\/\">datum<\/a> because it evaluates the surface against itself.<\/p><p>Flatness is often confused with surface roughness, but they describe different characteristics. Flatness controls the overall shape of a surface, while roughness describes its microscopic texture. A part can feel smooth and still fail flatness, or have a relatively rough surface and still meet its flatness tolerance.<\/p><h2>3. Key Differences: Straightness vs Flatness<\/h2><p>Straightness and flatness are both form tolerances that do not require a datum, but they are not interchangeable. Straightness controls a single line element or a center axis, while flatness controls an entire surface.<\/p><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"true\"><div><table class=\"ace-table\" data-ace-table-col-widths=\"193;368;249\"><colgroup> <col width=\"193\" \/> <col width=\"368\" \/> <col width=\"249\" \/><\/colgroup><thead><tr><th colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-L8mVdc6FVoEAH6xWmarcv6D9nlc\" style=\"text-align: left;\">Aspecto<\/div><\/th><th style=\"text-align: left;\" colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-CGoKdV40CoA2nAx8NUoczdg1n1g\">Straightness<\/div><\/th><th colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-GYLFdD536oxxiaxMuz4cIeKsn9d\" style=\"text-align: left;\">Flatness<\/div><\/th><\/tr><\/thead><tbody><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-EAEbd66ifoYnmGxxAWIc8KIhnEh\">What it controls<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-ZuAGd8HRloW4ePxRzSmcmL3vnbb\">A single line element or a center axis<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-H8Pbdga7qoGBydxJIqzc1gjbnHg\">An entire surface<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-RCROdgZWJomhX0xTlClclivLnff\">Dimension<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-EKNxdLbxfoWbHaxrDs2c05sjnMe\">2D (surface) or 3D (axis)<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-NXcQdfJr4oQHNyxScsvck69tndd\">3D<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-M8oDdVIfAoCJaIxgYb1cJOOpn1f\">Tolerance zone shape<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-MQ3Nd2DdIoXzwLxn9GCc46ganmp\">Two parallel lines (surface) or a cylinder (axis)<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-Yn4TdEF39oXrWexccUAcqkLensy\">Two parallel planes<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-UmZ9dffneoTwhfxoJEWcUpvTnLb\">Datum required<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-Co1fdSaM5onzl1xWaKkcmiz4nxc\">No<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-DQ6kdwp09oltCCx8qc4cuVXLn2b\">No<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-ZZFvdiqWgos0jfxlkGkcDSpHnxh\">Callout points to<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-Uoo4d9NMjoIje6xqbtqcTmwwnOh\">Surface or size dimension<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-JL5XdyBGIoc0OmxoDikcMz5Onig\">Surface<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-K4eldkvKRoRGcyxoEO7cx06Mnre\">Typical use<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-ZyRbdpu7yokMbHxBzCpc5G4qn6c\">Shafts, pins, guideways<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-GOiKdUVYmoY3s3xQrsHcFi6snwe\">Sealing faces, mounting surfaces<\/div><\/td><\/tr><\/tbody><\/table><p>Although the two tolerances look similar on a drawing, they serve different purposes and require different inspection methods. Parts that pass straightness may still fail flatness, and the opposite is also true.<\/p><p>As a practical rule, use flatness when the entire surface must make contact. Use straightness when the function depends on a line element or the axis of a cylindrical feature.<\/p><h2>4. When to Use Which: Practical Decision Guide<\/h2><p><img loading=\"lazy\" decoding=\"async\" src=\"data:image\/gif;base64,R0lGODlhAQABAIAAAAAAAP\/\/\/yH5BAEAAAAALAAAAAABAAEAAAIBRAA7\" data-src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide.jpg\" class=\"alignnone size-full wp-image-32740 lazyload\" alt=\"When to Use Which Practical Decision Guide\" width=\"1080\" height=\"550\"><noscript><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-32740\" src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide.jpg\" alt=\"When to Use Which Practical Decision Guide\" width=\"1080\" height=\"550\" srcset=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide.jpg 1080w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide-300x153.jpg 300w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide-1024x521.jpg 1024w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide-768x391.jpg 768w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/06\/When-to-Use-Which-Practical-Decision-Guide-18x9.jpg 18w\" sizes=\"(max-width: 1080px) 100vw, 1080px\" \/><\/noscript><\/p><p>The choice between straightness and flatness depends on how the feature functions in the assembly. A sealing face typically requires flatness, while a shaft with a bearing fit usually requires straightness. The examples below show the most common applications.<\/p><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"true\"><div><table class=\"ace-table\" data-ace-table-col-widths=\"268;168;401\"><colgroup> <col width=\"268\" \/> <col width=\"168\" \/> <col width=\"401\" \/><\/colgroup><thead><tr><th colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-ASIOd9991oMbihxtvD1ctX2knlc\" style=\"text-align: left;\">Part Type<\/div><\/th><th style=\"text-align: left;\" colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-DByUdGdAjoBbITx4WX6c7h0Xnye\">Use<\/div><\/th><th colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-Dd6AdWFOPorj8oxN67IcXEw7nye\" style=\"text-align: left;\">Why<\/div><\/th><\/tr><\/thead><tbody><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-NPl0dSXD7oGWRoxSTuOcXZNUnGc\">Shafts, pins, holes<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-QOZsdwBzRo9zxlx2fIJc2eumn8b\">Axis straightness<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-XXrTdjhD5ovVmvxNzKxc6BNtnWg\">Centerline must be straight for assembly without binding<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-DWendqasVocOpqxVP2ScGdbUn0d\">Guideways, sealing edges<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-A6WTdWjaNotsWKxJUUucHhu6nBh\">Surface straightness<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-OhdwdocwWo16jmxeOFYcHG8JnUh\">Only the contact line matters, not the whole face<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-NbO6dw7ieo7zOxxyBWncUifNnlh\">Sealing faces (valves, flanges)<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-E95jdRDpeoCxPxxcmJpcJt2unOf\">Flatness<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-QCd2dNVHFoE5rtxeDugcTKhOnrb\">Whole face must seal evenly to prevent leaks<\/div><\/td><\/tr><tr><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-L4wZdmIh8oTbqixv2DrcwL4gndf\">Mounting surfaces, bolted joints<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-TYCLdk2zuoPUDcx9EeFcmFebnge\">Flatness<\/div><\/td><td colspan=\"1\" rowspan=\"1\"><div class=\"ace-line ace-line old-record-id-IF7oduwYfocluix96GZcdg7Qnlw\">Even load distribution prevents distortion and loosening<\/div><\/td><\/tr><\/tbody><\/table><p>Different features require different GD&amp;T controls. Flatness is typically used when an entire surface must support, seal, or mount another component. Straightness is more appropriate when the function depends on a line element or the axis of a cylindrical feature. Selecting the appropriate tolerance helps ensure the required function without introducing unnecessary manufacturing or inspection requirements.<\/p><h2>5. Drawing Callouts and Measurement Methods<\/h2><p>The drawing callout tells the shop how a feature should be manufactured and tells the inspector how it should be verified. The specified tolerance and the inspection method go hand in hand. If the wrong control is applied, the inspection may not reflect the part&#8217;s actual functional requirement.<\/p><h5>Drawing Callouts<\/h5><p>Surface straightness and flatness are applied directly to a surface using a leader line. Surface straightness uses a tolerance zone defined by two parallel lines, while flatness uses two parallel planes. Axis straightness is different because it is applied to the size dimension of a cylindrical feature and uses a cylindrical tolerance zone.<\/p><h5>Measurement Methods<\/h5><p>Surface straightness is commonly checked with a dial indicator by measuring variation along a single line on the feature. Axis straightness is typically evaluated by rotating the part between centers or using dedicated inspection equipment to verify the center axis. Flatness requires measuring the entire surface, usually with a surface plate, height gage, or <a href=\"https:\/\/www.beskamold.com\/es\/what-is-cmm-inspection\/\">CMM<\/a> for larger or more complex parts.<\/p><p>In production, functional gages are often used for straightness inspection because they are much faster than CMMs when checking large quantities of parts. CMMs remain the preferred choice when higher accuracy or complete surface evaluation is required.<\/p><h5>Inspection Effort<\/h5><p>Inspection effort generally increases with the amount of geometry that must be evaluated. Surface straightness is usually the quickest to inspect because only a single line is measured. Axis straightness requires additional setup to evaluate the feature axis, while flatness typically takes the longest because the entire surface must be checked. For this reason, engineers usually specify the simplest tolerance that still meets the functional requirements of the part.<\/p><h2>6. Common Mistakes and Misconceptions in Straightness and Flatness<\/h2><p>Straightness and flatness are often confused because they appear similar on engineering drawings. However, applying the wrong control can lead to unnecessary inspection, higher manufacturing costs, or parts that pass inspection but fail in service. The following are some of the most common misconceptions.<\/p><h5>Straightness and Flatness Are Not Interchangeable<\/h5><p>Although both are form tolerances, they serve different functional purposes. A part may satisfy a straightness requirement along every measured line while still failing a flatness inspection because the overall surface is not controlled. Selecting one does not automatically satisfy the other.<\/p><h5>Flatness Does Not Replace Straightness<\/h5><p>Flatness controls the overall shape of a surface, but it does not guarantee that a specific edge or line element is straight. When a design depends on a straight sealing edge, guide edge, or similar functional feature, straightness should be specified separately if required.<\/p><h5>Surface Straightness and Axis Straightness Are Different Controls<\/h5><p>Although they share the same GD&amp;T symbol, surface straightness and axis straightness apply to different features and are verified using different inspection methods. Using the wrong callout may result in a part passing inspection while still failing its intended function.<\/p><h5>Flatness and Parallelism Are Different Requirements<\/h5><p>Flatness evaluates the shape of a single surface, while parallelism controls the orientation of one feature relative to a datum. A surface can meet its flatness tolerance but still fail a parallelism requirement if its orientation is incorrect.<\/p><p>Different GD&amp;T controls are designed for different functional requirements. Most of these misconceptions can be avoided by selecting the GD&amp;T control that best matches the function of the feature.<\/p><h2>Conclusi\u00f3n<\/h2><p>Straightness and flatness are closely related, but they solve different engineering problems. Choosing the appropriate control is less about specifying the tightest tolerance and more about matching the requirement to the function of the feature. Doing so helps ensure reliable assembly, appropriate inspection, and efficient manufacturing.<\/p><p>In our experience, reviewing GD&amp;T callouts early in the design stage often helps identify unnecessary or incorrectly specified tolerances before production begins. This not only simplifies manufacturing and inspection but also reduces the risk of unexpected quality issues during assembly.<\/p><p>At Beska, every <a href=\"https:\/\/www.beskamold.com\/es\/proveedor-de-servicios-de-mecanizado-cnc\/\">Mecanizado CNC<\/a> project begins with a review of the engineering drawing. We evaluate GD&amp;T requirements, including straightness and flatness, to confirm they are practical for manufacturing and appropriate for the function of the part. This helps us produce precision-machined components that meet design intent while avoiding unnecessary machining complexity.<\/p><h2>Preguntas frecuentes<\/h2><\/div><\/div><\/div><\/div>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t<div class=\"elementor-element elementor-element-03dc4e7 e-flex e-con-boxed e-con e-parent\" data-id=\"03dc4e7\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t\t<div class=\"e-con-inner\">\n\t\t\t\t<div class=\"elementor-element elementor-element-6802c2b uael-faq-box-layout-yes align-at-left elementor-widget elementor-widget-uael-faq\" data-id=\"6802c2b\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"uael-faq.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\n\t\t\t<div id='uael-faq-wrapper-109' class=\"uael-faq-wrapper\">\n\t\t\t\t<div class=\"uael-faq-container uael-faq-layout-accordion\" data-layout=\"accordion\" >\n\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-8c9d247\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-8c9d247 uael-question-span\" tabindex=\"0\" id=\"uael-faq-1\">Should a shaft use surface straightness or axis straightness?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><p>Axis straightness is typically used for shafts that fit into bearings, bushings, or precision holes because it controls the center axis. Surface straightness is more appropriate when the function depends on the straightness of the shaft surface, such as a guide or sealing edge. The correct choice depends on how the feature functions in the assembly.<\/p><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-f08a1eb\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-f08a1eb uael-question-span\" tabindex=\"0\" id=\"uael-faq-2\">Can straightness and flatness be applied to the same feature?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><p>Yes. Straightness and flatness control different characteristics and can both be specified when required. Whether both controls are necessary depends on the functional requirements of the feature rather than the type of part.<\/p><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-c7390df\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-c7390df uael-question-span\" tabindex=\"0\" id=\"uael-faq-3\"> Why does a sealed surface still leak with a flatness callout?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><p>Flatness controls the overall shape of a surface, not its texture. A surface may meet its flatness requirement but still be too rough to form an effective seal. Sealing surfaces often require both an appropriate flatness tolerance and a suitable surface finish specification.<\/p><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-b9fdc58\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-b9fdc58 uael-question-span\" tabindex=\"0\" id=\"uael-faq-4\">What if a part passes straightness inspection but still does not fit?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><p>The wrong type of straightness may have been specified. Surface straightness controls individual line elements, while axis straightness controls the center axis of a cylindrical feature. For shafts that fit into bearings or precision holes, axis straightness is usually the more appropriate control.<\/p><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-becaf4c\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-becaf4c uael-question-span\" tabindex=\"0\" id=\"uael-faq-5\">Can flatness replace parallelism?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><p>No. Flatness controls the shape of a single surface, while parallelism controls the orientation of one feature relative to a datum. A surface may satisfy its flatness requirement but still fail a parallelism requirement if its orientation is incorrect.<\/p><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>","protected":false},"excerpt":{"rendered":"<p>Two engineering drawings may look almost identical. One specifies straightness, while the other specifies flatness. The difference seems minor, but it can affect how a part is machined, inspected, and assembled. Straightness and flatness are both GD&amp;T form tolerances, but they control different aspects of a part&#8217;s geometry. Straightness controls a single line or axis, [&hellip;]<\/p>\n","protected":false},"author":12,"featured_media":32749,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[47],"tags":[],"class_list":["post-32736","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/posts\/32736","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/users\/12"}],"replies":[{"embeddable":true,"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/comments?post=32736"}],"version-history":[{"count":0,"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/posts\/32736\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/media\/32749"}],"wp:attachment":[{"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/media?parent=32736"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/categories?post=32736"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.beskamold.com\/es\/wp-json\/wp\/v2\/tags?post=32736"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}