{"id":33830,"date":"2026-09-07T02:19:53","date_gmt":"2026-09-07T02:19:53","guid":{"rendered":"https:\/\/www.beskamold.com\/?p=33830"},"modified":"2026-09-07T02:26:48","modified_gmt":"2026-09-07T02:26:48","slug":"k-factor-in-sheet-metal-bending","status":"publish","type":"post","link":"https:\/\/www.beskamold.com\/fr\/k-factor-in-sheet-metal-bending\/","title":{"rendered":"What Is K-Factor in Sheet Metal Bending? Formula &#038; Uses"},"content":{"rendered":"\t\t<div data-elementor-type=\"wp-post\" data-elementor-id=\"33830\" class=\"elementor elementor-33830\" data-elementor-post-type=\"post\">\n\t\t\t\t<div class=\"elementor-element elementor-element-1569544 e-flex e-con-boxed e-con e-parent\" data-id=\"1569544\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t\t<div class=\"e-con-inner\">\n\t\t\t\t<div class=\"elementor-element elementor-element-2742aef elementor-widget elementor-widget-text-editor\" data-id=\"2742aef\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"text-editor.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\t\t\t\t<p>A <a href=\"https:\/\/www.beskamold.com\/sheet-metal-forming-service\/\">sheet metal part<\/a> can look correct in CAD and still come off the press brake with flange lengths or hole positions that do not match the drawing. In many cases, the problem starts with how the bend is unfolded into a flat pattern.<\/p><p>During bending, the neutral axis shifts away from the middle of the sheet, and K-factor describes its position relative to the material thickness. That value affects bend allowance and therefore the final flat-pattern dimensions. Material, bend radius, tooling, and forming method can all influence the result, which is why a single default K-factor does not work equally well for every bending condition.<\/p><h2>1. What Is the Neutral Axis?<br \/><img fetchpriority=\"high\" decoding=\"async\" src=\"data:image\/gif;base64,R0lGODlhAQABAIAAAAAAAP\/\/\/yH5BAEAAAAALAAAAAABAAEAAAIBRAA7\" data-src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis.jpg\" class=\"alignnone size-full wp-image-33835 lazyload\" alt=\"What Is the Neutral Axis\" width=\"1080\" height=\"550\"><noscript><img decoding=\"async\" class=\"alignnone size-full wp-image-33835\" src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis.jpg\" alt=\"What Is the Neutral Axis\" width=\"1080\" height=\"550\" srcset=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis.jpg 1080w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis-300x153.jpg 300w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis-1024x521.jpg 1024w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis-768x391.jpg 768w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/What-Is-the-Neutral-Axis-18x9.jpg 18w\" sizes=\"(max-width: 1080px) 100vw, 1080px\" \/><\/noscript><\/h2><p>When sheet metal is bent, the material on the outside of the bend is stretched while the material on the inside is compressed. Between these two regions lies the neutral axis, where the longitudinal strain is approximately zero.<\/p><p>In a flat, uniform sheet, this reference position is near the middle of the thickness. During plastic bending, the neutral axis generally shifts toward the inside of the bend. K-factor describes the location of this neutral axis relative to the material thickness.<\/p><p>This matters because the length of the neutral axis through the bend is used to calculate <a href=\"https:\/\/www.beskamold.com\/what-is-bend-allowance\/\">bend allowance<\/a>. Its position therefore affects the flat-pattern length needed to produce the required flange dimensions after bending.<\/p><h2>2. What Is the K-Factor?<\/h2><p>The K-factor describes the position of the neutral axis through the sheet thickness. It is calculated as the distance from the inside surface of the bend to the neutral axis divided by the material thickness.<\/p><p><strong>K = t \/ T<\/strong><\/p><p>Where:<\/p><ul><li>t = distance from the inside surface to the neutral axis<\/li><li>T = material thickness<\/li><\/ul><p>For example, if the neutral axis is located at 44% of the material thickness measured from the inside surface, the K-factor is 0.44.<\/p><p>K-factor values are commonly expressed between about 0.30 and 0.50, depending on the material and bending conditions. A value of 0.50 places the neutral axis at the middle of the sheet thickness, while a lower value places it closer to the inside surface.<\/p><p>Because the neutral-axis position changes with the actual bending conditions, the K-factor should be treated as a process-dependent value rather than a fixed material property.<\/p><h2>3. How Forming Method and Bend Radius Affect K-Factor<\/h2><p>The K-factor is influenced by the actual bend geometry, especially the relationship between the inside bend radius and material thickness. A change in tooling or forming method can change the inside radius, which in turn affects the neutral-axis position used in flat-pattern calculations.<\/p><table><colgroup> <col width=\"294\" \/> <col width=\"294\" \/> <col width=\"294\" \/><\/colgroup><tbody><tr><td><strong>Forming Method<\/strong><\/td><td><strong>Typical Bend Behavior<\/strong><\/td><td><strong>Effect on K-Factor Calculations<\/strong><\/td><\/tr><tr><td>Air Bending<\/td><td>Inside radius depends strongly on the V-die opening, material, and tooling setup<\/td><td>Bend data may change when the die opening or tooling changes<\/td><\/tr><tr><td>Bottoming<\/td><td>Material is formed more closely to the punch and die geometry<\/td><td>Bend radius is generally more controlled, but material and tooling still affect the result<\/td><\/tr><tr><td>Coining<\/td><td>Very high pressure forces the material closely into the tooling<\/td><td>Can reduce springback, but requires much higher forming force<\/td><\/tr><\/tbody><\/table><p>The radius-to-thickness ratio (R\/T) is also important. A tight bend and a large-radius bend do not deform the material in the same way, so the same K-factor should not automatically be assumed for both.<\/p><p>For production parts, the bend data used in CAD should match the material, thickness, inside radius, and tooling actually used on the press brake. If any of these conditions change, the flat pattern may need to be verified again.<\/p><h2>4. How K-Factor Is Used in Bend Allowance<\/h2><p>K-factor becomes useful when calculating bend allowance, which represents the length of the neutral axis through the bend. This value is used when developing the flat pattern of a bent sheet metal part.<br \/>The bend allowance formula is:<br \/>BA = A \u00d7 (R + K \u00d7 T)<\/p><p>Where:<\/p><ul><li>BA = bend allowance<\/li><li>A = bend angle in radians<\/li><li>R = inside <a href=\"https:\/\/www.beskamold.com\/sheet-metal-bend-radius\/\">bend radius<\/a><\/li><li>K = K-factor<\/li><li>T = material thickness<\/li><\/ul><p>If the bend angle is given in degrees:<\/p><p>BA = (\u03c0 \/ 180) \u00d7 A \u00d7 (R + K \u00d7 T)<\/p><p>For example, a 90\u00b0 bend and a 45\u00b0 bend with the same material thickness, inside radius, and K-factor will have different bend allowances because the neutral-axis arc length changes with the bend angle.<\/p><p>Bend allowance can then be used together with flange geometry to determine the required flat length. Where bend deduction is used instead, it can be calculated from the outside setback and bend allowance:<\/p><p>BD = 2 \u00d7 OSSB \u2212 BA<br \/>with: OSSB = tan(A \/ 2) \u00d7 (R + T)<\/p><p>The same bend-angle convention should be used consistently throughout the calculation.<\/p><p><img decoding=\"async\" src=\"data:image\/gif;base64,R0lGODlhAQABAIAAAAAAAP\/\/\/yH5BAEAAAAALAAAAAABAAEAAAIBRAA7\" data-src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance.jpg\" class=\"alignnone size-full wp-image-33836 lazyload\" alt=\"How K Factor Is Used in Bend Allowance\" width=\"1080\" height=\"550\"><noscript><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-33836\" src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance.jpg\" alt=\"How K Factor Is Used in Bend Allowance\" width=\"1080\" height=\"550\" srcset=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance.jpg 1080w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance-300x153.jpg 300w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance-1024x521.jpg 1024w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance-768x391.jpg 768w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/How-K-Factor-Is-Used-in-Bend-Allowance-18x9.jpg 18w\" sizes=\"(max-width: 1080px) 100vw, 1080px\" \/><\/noscript><\/p><h2>5. K-Factor vs Y-Factor<\/h2><p>K-factor and Y-factor are both used in sheet metal bend calculations, but they are expressed differently. In systems that use the common relationship between the two:<\/p><p><strong>Y = K \u00d7 \u03c0 \/ 2<\/strong><\/p><p>K-factor describes the position of the neutral axis as a ratio of material thickness, while Y-factor is another parameter used by some CAD and sheet metal calculation systems.<\/p><p>For most design work, the important point is consistency. The value and calculation method used in CAD should match the bend table or manufacturing data used for the actual material, radius, and tooling. Switching between K-factor and Y-factor does not correct an inaccurate flat pattern if the underlying bend data is wrong.<\/p><h2>6. What Affects K-Factor in Production<\/h2><p>K-factor is influenced by the actual bending conditions rather than by material grade alone. Changes in material, thickness, bend geometry, or tooling can all affect the neutral-axis position and the resulting flat pattern.<\/p><h5>Material and Thickness<\/h5><p>Different alloys, strength levels, and tempers respond differently during bending. Material thickness also matters because it changes the relationship between the sheet and the bend radius. For this reason, a K-factor established for one material and thickness should not automatically be applied to another.<\/p><h5>Bend Radius and Tooling<\/h5><p>The actual inside radius has a direct influence on the bend geometry. Changes in die opening, punch geometry, tooling condition, or press-brake setup can therefore change the bend data used for flat-pattern development.<\/p><h5>Material Variation and Grain Direction<\/h5><p>Material properties can vary between grades, tempers, and production lots. Grain direction may also influence bending behavior, especially where formability and springback are sensitive to bend orientation.<\/p><p>For repeat production, it is more reliable to maintain bend data for the actual combinations of material, thickness, bend radius, and tooling used in the shop, and to verify the flat pattern when those conditions change.<\/p><h2>7. How to Determine K-Factor in Production<\/h2><p>A practical way to establish a K-factor for a specific bending setup is to run a test bend using the same material, thickness, tooling, and press-brake conditions planned for production.<\/p><ul><li>Step 1: Cut a flat test blank and record its dimensions.<\/li><li>Step 2: Bend the sample to the required angle using the intended tooling and machine setup.<\/li><li>Step 3: Measure the formed flange dimensions and the actual inside bend radius.<\/li><li>Step 4: Determine the bend allowance from the measured geometry using a consistent dimensional reference.<\/li><li>Step 5: Calculate the K-factor from the bend allowance equation: K = [BA \/ (A \u00d7 T)] \u2212 (R \/ T)<\/li><\/ul><p>Where:<\/p><ul><li>BA = measured bend allowance<\/li><li>A = bend angle in radians<\/li><li>T = material thickness<\/li><li>R = inside bend radius<\/li><\/ul><p>This equation comes directly from: <strong>BA = A \u00d7 (R + K \u00d7 T)<\/strong><\/p><p>The resulting K-factor reflects the actual combination of material, thickness, bend radius, tooling, and machine setup. For repeat production, these measured values can be stored in a bend table and reused when the same bending conditions apply.<\/p><h2>8. K-Factor Calculation Example<\/h2><p>Consider a 90\u00b0 bend in 1.5 mm sheet metal with a 1.5 mm inside radius.<\/p><p>The bend angle in radians is: 90 \u00d7 (\u03c0 \/ 180) = 1.5708<\/p><p>Using a K-factor of 0.446:<\/p><ul><li>BA = 1.5708 \u00d7 (1.5 + 0.446 \u00d7 1.5)<\/li><li>BA \u2248 3.41 mm<\/li><\/ul><p>Using a K-factor of 0.33:<\/p><ul><li>BA = 1.5708 \u00d7 (1.5 + 0.33 \u00d7 1.5)<\/li><li>BA \u2248 3.13 mm<\/li><\/ul><p>The difference is about 0.27 mm for a single bend. If the same difference occurs across four bends, the total flat-development difference can approach 1.1 mm.<\/p><p>For parts with several bends, short flanges, or closely positioned mounting holes, this difference can become significant. The example shows why the K-factor used in CAD should reflect the actual material, bend radius, and tooling rather than being treated as a fixed default value.<\/p><h2><img loading=\"lazy\" decoding=\"async\" src=\"data:image\/gif;base64,R0lGODlhAQABAIAAAAAAAP\/\/\/yH5BAEAAAAALAAAAAABAAEAAAIBRAA7\" data-src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example.jpg\" class=\"alignnone size-full wp-image-33837 lazyload\" alt=\"K Factor Calculation Example\" width=\"1080\" height=\"550\"><noscript><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-33837\" src=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example.jpg\" alt=\"K Factor Calculation Example\" width=\"1080\" height=\"550\" srcset=\"https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example.jpg 1080w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example-300x153.jpg 300w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example-1024x521.jpg 1024w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example-768x391.jpg 768w, https:\/\/www.beskamold.com\/wp-content\/uploads\/2026\/09\/K-Factor-Calculation-Example-18x9.jpg 18w\" sizes=\"(max-width: 1080px) 100vw, 1080px\" \/><\/noscript><\/h2><h2>9. Typical K-Factor Starting Values<\/h2><p>Published K-factor values can be useful during early design, but they should be treated as starting points rather than fixed material constants. The actual value can change with material condition, thickness, inside bend radius, tooling, and forming method.<\/p><table><colgroup> <col width=\"353\" \/> <col width=\"353\" \/><\/colgroup><tbody><tr><td><strong>Material<\/strong><\/td><td><strong>Common Starting Range<\/strong><\/td><\/tr><tr><td>Mild steel<\/td><td>~0.40\u20130.45<\/td><\/tr><tr><td>Stainless steel<\/td><td>~0.40\u20130.50<\/td><\/tr><tr><td>Aluminum alloys<\/td><td>~0.33\u20130.45<\/td><\/tr><tr><td>Copper and brass<\/td><td>Varies with alloy and temper<\/td><\/tr><\/tbody><\/table><p>These ranges are only approximate. Two parts made from the same material can require different K-factors if the thickness, bend radius, tooling, or forming method changes.<\/p><p>For production work, bend-test data or a validated shop bend table is more reliable than selecting a K-factor from a general material table.<\/p><h2>10. K-Factor vs Bend Deduction<\/h2><p>K-factor and bend deduction are both used to develop sheet metal flat patterns, but they describe different parts of the calculation.<\/p><table><colgroup> <col width=\"236\" \/> <col width=\"236\" \/> <col width=\"236\" \/><\/colgroup><tbody><tr><td><strong>Method<\/strong><\/td><td><strong>What It Represents<\/strong><\/td><td><strong>Typical Use<\/strong><\/td><\/tr><tr><td>K-Factor<\/td><td>Neutral-axis position relative to material thickness<\/td><td>Bend allowance calculations and CAD bend tables<\/td><\/tr><tr><td>Bend Deduction<\/td><td>Amount subtracted from the sum of outside flange dimensions to obtain the flat length<\/td><td>Shop bend tables and direct flat-pattern calculations<\/td><\/tr><\/tbody><\/table><p>K-factor is used to calculate bend allowance, while bend deduction converts the formed outside dimensions directly into a flat length. The two methods are related through bend allowance and outside setback rather than being separate ways of describing the material itself.<\/p><p>In production, either method can work when the values are based on the actual material, bend radius, tooling, and bend angle. The important point is that the CAD model and shop bend data use the same calculation method and validated bending conditions.<\/p><h2>Conclusion<\/h2><p>K-factor describes the position of the neutral axis through the sheet thickness and directly affects bend allowance and flat-pattern dimensions. It should not be treated as a fixed material constant, since the actual value can change with material condition, thickness, inside bend radius, tooling, and forming method.<\/p><p>For production parts, the bend data used in CAD should match the actual forming conditions as closely as possible. Test bends and validated bend tables are especially useful when flange lengths, hole positions, or multiple bends leave little room for accumulated flat-pattern error.<\/p><p>If your sheet metal drawing includes critical bend dimensions, <a href=\"https:\/\/www.beskamold.com\/contact-us\/\">Beska<\/a> can review the material thickness, bend radius, K-factor, and flat-pattern setup together before production, helping identify potential unfolding or bend-allowance issues before the blanks are cut.<\/p><h2>FAQ<\/h2>\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t<div class=\"elementor-element elementor-element-42b7f93 e-flex e-con-boxed e-con e-parent\" data-id=\"42b7f93\" data-element_type=\"container\" data-e-type=\"container\">\n\t\t\t\t\t<div class=\"e-con-inner\">\n\t\t\t\t<div class=\"elementor-element elementor-element-9134d98 uael-faq-box-layout-yes align-at-left elementor-widget elementor-widget-uael-faq\" data-id=\"9134d98\" data-element_type=\"widget\" data-e-type=\"widget\" data-widget_type=\"uael-faq.default\">\n\t\t\t\t<div class=\"elementor-widget-container\">\n\t\t\t\t\t\n\t\t\t<div id='uael-faq-wrapper-152' class=\"uael-faq-wrapper\">\n\t\t\t\t<div class=\"uael-faq-container uael-faq-layout-accordion\" data-layout=\"accordion\" >\n\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-d3e03cc\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-d3e03cc uael-question-span\" tabindex=\"0\" id=\"uael-faq-1\">How often should K-factor be verified?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"false\"><div class=\" old-record-id-JkNudmAm4oi4dXxBIdZcTvMOnug\">K-factor should be checked when the material grade, thickness, tooling, bend radius, or forming setup changes. For critical parts, periodic verification is also useful because tooling wear and material variation can affect the actual bend result.<\/div><\/div><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-00d41c1\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-00d41c1 uael-question-span\" tabindex=\"0\" id=\"uael-faq-2\">Does K-factor change with bend angle?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"false\"><div class=\" old-record-id-AHOIdMhqgoNoekxQo4BcD52QnPh\">It can. Bend angle is one of several factors that may affect the actual bending behavior, although material condition, radius-to-thickness ratio, and tooling are often equally important. For accurate production work, bend data should reflect the angles actually used.<\/div><\/div><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-cac3bd4\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-cac3bd4 uael-question-span\" tabindex=\"0\" id=\"uael-faq-3\">Can K-factor be greater than 0.5?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"false\"><div class=\" old-record-id-TJWMdIfm6o35cSxGS60c4zuZnjf\">In common sheet-metal bending calculations, K-factor is typically at or below 0.5 because the neutral axis is usually located at or inside the mid-thickness of the sheet. If a calculated value is above 0.5, the measurement method, bend-angle definition, and input dimensions should be checked.<\/div><\/div><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-58648f5\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-58648f5 uael-question-span\" tabindex=\"0\" id=\"uael-faq-4\">Does sheet thickness affect K-factor?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"false\"><div class=\" old-record-id-Is8Fdc3nrovfOExfBiYcvAexntg\">Yes, but not independently. Thickness changes the relationship between the material and the inside bend radius, so the same K-factor should not automatically be transferred between different thicknesses, even for the same alloy.<\/div><\/div><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-652ccea\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-652ccea uael-question-span\" tabindex=\"0\" id=\"uael-faq-5\">Can I use the same K-factor for aluminum and steel?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"false\"><div class=\" old-record-id-RK8kdE9oxoSvVBxErI6cRmK9nvd\">It should not be assumed. Aluminum and steel have different mechanical properties and can respond differently to the same bend geometry and tooling. Production values should be based on the actual material and bending conditions.<\/div><\/div><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t\t\t\t<div id=\"uael-accordion-7a74539\" class=\"uael-faq-accordion\" role=\"tablist\">\n\t\t\t\t\t\t\t\t<div class= \"uael-accordion-title\" aria-expanded=\"false\" role=\"tab\">\n\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon uael-accordion-icon-left\">\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-closed\"><i class=\"fas fa-angle-right\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t\t<span class=\"uael-accordion-icon-opened\"><i class=\"fas fa-angle-up\"><\/i><\/span>\n\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t\t<span class=\"uael-question-7a74539 uael-question-span\" tabindex=\"0\" id=\"uael-faq-6\">Why does my CAD flat pattern differ from the part produced on the press brake?<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t<div class=\"uael-accordion-content\" role=\"tabpanel\">\n\t\t\t\t\t\t\t\t\t<span>\n\t\t\t\t\t\t\t\t\t<span><div data-page-id=\"H8PrdHHajow3M1xcfTmcXCfsnVf\" data-lark-html-role=\"root\" data-docx-has-block-data=\"false\"><div class=\" old-record-id-JUvJdsSrOo0Tanx3065c0Zl7nCb\">The bend data in CAD may not match the actual material, inside radius, tooling, or forming method used in production. A test bend can help verify the bend allowance and update the K-factor or bend table before production.<\/div><\/div><\/span>\t\t\t\t\t\t\t\t\t<\/span>\n\t\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t\t\t\t\t\t\t\t<\/div>\n\t\t\t<\/div>\n\t\t\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t\t\t<\/div>\n\t\t","protected":false},"excerpt":{"rendered":"<p>A sheet metal part can look correct in CAD and still come off the press brake with flange lengths or hole positions that do not match the drawing. In many cases, the problem starts with how the bend is unfolded into a flat pattern. During bending, the neutral axis shifts away from the middle of [&hellip;]<\/p>\n","protected":false},"author":12,"featured_media":33846,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_acf_changed":false,"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[47],"tags":[],"class_list":["post-33830","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-blog"],"acf":[],"_links":{"self":[{"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/posts\/33830","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/users\/12"}],"replies":[{"embeddable":true,"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/comments?post=33830"}],"version-history":[{"count":0,"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/posts\/33830\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/media\/33846"}],"wp:attachment":[{"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/media?parent=33830"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/categories?post=33830"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.beskamold.com\/fr\/wp-json\/wp\/v2\/tags?post=33830"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}